EDIT YOUR PROFILE HERE

Forum breadcrumbs - You are here:ForumUnread Topics
Please or Register to create posts and topics.

Unread Topics

PreviousPage 2 of 12Next
Mark All Read
Adding "Laser On" LED to custom control panelIn Fine tuning performance · 3 years ago
Mini Gerbil3 ploblem doing a burnIn Troubleshooting · 3 years ago
What is the pin out of the alternate end stop connector J5In Installation issues · 6 years ago
problem mini gerbil 3In Troubleshooting · 3 years ago
K40 producing lots of Dots in engravingIn Help with installing the Gerbil controller · 3 years ago
Help - different power supply!In Help with installing the Gerbil controller · 3 years ago
K40 Laser Power Before & AfterIn Help with installing the Gerbil controller · 8 years ago
Laser not turning offIn Fine Tuning performance · 4 years ago
60Watt InstallIn MG3 installation · 3 years ago
MG3 PINOUT MAPIn Help with installing the Gerbil controller · 3 years ago
Engraving quality, ImagR-KasiaIn Fine tuning performance · 3 years ago
Y axis getting hotIn Troubleshooting chart · 3 years ago
MG2 to MG3In Fine tuning performance · 3 years ago
Purchased licensesIn LightBurn licenses · 3 years ago
Other K40 forums that might be helpfulIn Help with installing the Gerbil controller · 3 years ago
External Stepper Drivers MG3In MG3 installation · 3 years ago
PWMIn MG3 installation · 3 years ago
Laser BandingIn Other issues or suggestions · 3 years ago
MG3 trouble shootingIn Troubleshooting · 3 years ago
Customisation Air assist portIn Fine tuning performance · 3 years ago
K40 Stepper MotorIn General instructions and rules for this forum · 3 years ago
GrayscaleIn Vitamins for the K40 · 3 years ago
Power to the boardIn Help with installing the Gerbil controller · 3 years ago
upgrading limit switchesIn All things related to legacy Gerbils · 5 years ago
LaserGrbl 4.7.1 works with smoothie settingIn Laserweb configuration · 4 years ago
Drv8825 Drivers?In Fine Tuning performance · 4 years ago
M2 Nano mainboard have problem can not cut SquareIn General instructions and rules for this forum · 4 years ago
Stock Availability?In Other issues or suggestions · 4 years ago
Y axis is shrunken when I draw a perfect squareIn LightBurn G-code device driver · 4 years ago
Laser dont shut offIn Other issues or suggestions · 4 years ago
Waste of timeIn General instructions and rules for this forum · 4 years ago
16mm momentary and latching push Button switch wiring helpIn Help with installing the Gerbil controller · 4 years ago
Major headacheIn Help with installing the Gerbil controller · 4 years ago
Install of flow sensorIn Installation issues · 4 years ago
No movement axis Y and X only vibratesIn Troubleshooting chart · 4 years ago
LCD screenIn Vitamins for the K40 · 4 years ago
Light and power switches analogueIn Installation issues · 4 years ago
Gerbil randomly freezes during engraveIn Troubleshooting chart · 4 years ago
No movement using minigerbil with lightburnIn Troubleshooting chart · 4 years ago
No Laser Output/FireIn Installation issues · 4 years ago
No movementIn What does alarm <n> mean? · 4 years ago
No movementIn Help with installing the Gerbil controller · 4 years ago
New Mini Gerbil and Rotary Switch issuesIn Help with installing the Gerbil controller · 4 years ago
Install went well but issues with Lightburn?In Help with installing the Gerbil controller · 4 years ago
Mini Gerbil Installed, Moved once and Never Moved AgainIn Installation issues · 4 years ago
Text Ghosting on FillIn Help with installing the Gerbil controller · 4 years ago
K40 Fires at 100% even Thru Moves MiniGRBLIn Troubleshooting chart · 4 years ago
Different K40 power supply and newer mini gerbil board install helpIn Help with installing the Gerbil controller · 6 years ago
GRBL Version / ChangesIn Using Gerbil Plugins · 8 years ago
Limit switches - Induction Proximity Detectors SN04In Installation issues · 4 years ago
PreviousPage 2 of 12Next
Mark All Read

Forum Registration

EDIT YOUR PROFILE HERE