EDIT YOUR PROFILE HERE

Please or Register to create posts and topics.

Fine Tuning performance

Fine Tuning performance
TopicsLast post
Move a License from Old to New computerBy Paul0 Replies · 1,261 ViewsLast post: 5 years ago · Paul
Paul
5 years ago
Paul
Laser not turning offBy riley123419811 Replies · 2,249 ViewsLast post: 4 years ago · okmatt
okmatt
4 years ago
okmatt
Drv8825 Drivers?By Norm Dressler1 Reply · 662 ViewsLast post: 4 years ago · dancolwp1974
Daniel Collins
4 years ago
dancolwp1974
What am i doing wrong? line engraving not connecting on cornersBy Mark Rylett2 Replies · 2,128 ViewsLast post: 5 years ago · dancolwp1974
Daniel Collins
5 years ago
dancolwp1974
Moving BackwardsBy Shawn Hollett3 Replies · 881 ViewsLast post: 5 years ago · Paul
Paul
5 years ago
Paul
Softer direction changes while rasteringBy Rob Hertlein1 Reply · 805 ViewsLast post: 5 years ago · dancolwp1974
Daniel Collins
5 years ago
dancolwp1974
Poor performance and rendering qualityBy Matthew Spencer5 Replies · 1,448 ViewsLast post: 5 years ago · dancolwp1974
Daniel Collins
5 years ago
dancolwp1974
Skipping steps please help.By mjhall2911 Replies · 1,748 ViewsLast post: 5 years ago · mjhall29
Martin Hall
5 years ago
mjhall29
Minimum PWM OutputBy Nathan Caswell8 Replies · 1,827 ViewsLast post: 5 years ago · dancolwp1974
Daniel Collins
5 years ago
dancolwp1974
Dialing in photo quality engravingBy Paul0 Replies · 803 ViewsLast post: 5 years ago · Paul
Paul
5 years ago
Paul
TMC2209 stepsticksBy Zig11002 Replies · 1,300 ViewsLast post: 5 years ago · Zig1100
Zig1100
5 years ago
Zig1100
MG New installation & resultsBy dat-alex1 Reply · 896 ViewsLast post: 5 years ago · Paul
Paul
5 years ago
Paul
Laser pulse rise timeBy Peter Harrison0 Replies · 843 ViewsLast post: 5 years ago · Peter Harrison
Peter Harrison
5 years ago
Peter Harrison
Traversal Lines have STARTED to occurBy Pete Outen3 Replies · 848 ViewsLast post: 5 years ago · Paul
Paul
5 years ago
Paul
Big change in raster detail...By Scott Noble1 Reply · 1,022 ViewsLast post: 6 years ago · Dan
Daniel Collins
6 years ago
Dan
Poor Quality Raster EngravingBy Tom Lehman3 Replies · 2,534 ViewsLast post: 6 years ago · Tom Lehman
Tom Lehman
6 years ago
Tom Lehman
Laser speed increases on smaller parts of fillBy Tobi Horn1 Reply · 775 ViewsLast post: 6 years ago · Paul
Paul
6 years ago
Paul
Changing Power settings (S Value)By Rob Hertlein3 Replies · 1,370 ViewsLast post: 6 years ago · Paul
Paul
6 years ago
Paul
MAX speed using mini GRBLBy Daniel cala1 Reply · 1,066 ViewsLast post: 6 years ago · Paul
Paul
6 years ago
Paul
default mini settingsBy riley12341981 Reply · 961 ViewsLast post: 6 years ago · Paul
Paul
6 years ago
Paul
Unable to increase power above 20%By samm223 Replies · 924 ViewsLast post: 6 years ago · Paul
Paul
6 years ago
Paul
Need Help with Homing IssueBy Flex1 · 
12
20 Replies · 3,717 ViewsLast post: 6 years ago · Paul
Paul
6 years ago
Paul
SpeedBy riley12341981 Reply · 1,571 ViewsLast post: 6 years ago · HumptyDumpty
HumptyDumpty
6 years ago
HumptyDumpty
Adding additional power supplyBy Joel Rybacki2 Replies · 1,159 ViewsLast post: 6 years ago · Joel Rybacki
Joel Rybacki
6 years ago
Joel Rybacki
Mini Gerbil fine tuningBy Paul3 Replies · 3,413 ViewsLast post: 7 years ago · Paul
Paul
7 years ago
Paul
Can I add TMC2208 Stepper drivers?By Roy2 Replies · 1,894 ViewsLast post: 7 years ago · Roy
Roy
7 years ago
Roy

Forum Registration

EDIT YOUR PROFILE HERE