EDIT YOUR PROFILE HERE

Forum breadcrumbs - You are here:ForumUnread Topics
Please or Register to create posts and topics.

Unread Topics

Page 1 of 12Next
Mark All Read
Mini Gerbil 3 air assist wiring problem..In Troubleshooting · 5 months ago
MG2 suddenly detected as unknown usb device win10In Troubleshooting chart · 8 months ago
Lost USB connectionIn Troubleshooting · 3 years ago
Weird problem with K40 X axisIn Other issues or suggestions · 9 months ago
MG3 Install ExperienceIn MG3 installation · 10 months ago
60W laser - no 5V on power plugIn Help with installing the Gerbil controller · 11 months ago
No Movement from SteppersIn Troubleshooting · 1 year ago
Low laser power output from Lightburn via MG3In Help with installing the Gerbil controller · 1 year ago
Photo's of the drag chain installedIn Installing the drag chain · 8 years ago
What are the best point to source power?In Vitamins for the K40 · 1 year ago
Ummm Help? Stream not completingIn Troubleshooting · 1 year ago
Different K40 with different wiringIn Help with installing the Gerbil controller · 2 years ago
On-device head positioning.In Other issues or suggestions · 2 years ago
k40 with digital control panel questionsIn Help with installing the Gerbil controller · 1 year ago
No voltage to stepper motors 2-25-2025In Help with installing the Gerbil controller · 1 year ago
Recommended stepper motors for MG3 on K40In Fine tuning performance · 1 year ago
targeting laserIn MG3 installation · 2 years ago
Air output (optional outputs)In MG3 installation · 2 years ago
Laser not burningIn What does alarm <n> mean? · 2 years ago
Rotary attachmentIn MG3 installation · 2 years ago
Order receiptIn Purchase, response and emails · 2 years ago
Ordered but nothing so farIn Purchase, response and emails · 2 years ago
PWM/Power control issuesIn Troubleshooting · 2 years ago
mini Gerbel firing before jobIn Other issues or suggestions · 2 years ago
MiniGerbil - Test Fire too HotIn Help with installing the Gerbil controller · 2 years ago
Air assist solenoid valveIn Installation issues · 2 years ago
MG3 not driving the motorsIn Troubleshooting · 2 years ago
Software before getting Lightburn licenseIn Other issues or suggestions · 3 years ago
Engraviring problemIn Fine tuning performance · 2 years ago
K40 50W problem tube sound and performanceIn Troubleshooting · 3 years ago
Solid state relay wiringIn Fine tuning performance · 3 years ago
Removing potentiometer and test fire buttonIn Fine tuning performance · 3 years ago
No PWM Control, non standard PSUIn MG3 installation · 3 years ago
Need help, nothing workingIn Help with installing the Gerbil controller · 3 years ago
Laser low powerIn General instructions and rules for this forum · 3 years ago
Test fire?In General instructions and rules for this forum · 4 years ago
Is Mac Big Sur compatible with mini gerbil v3?In General instructions and rules for this forum · 3 years ago
MB2 Motor controllersIn Troubleshooting chart · 3 years ago
Analog Potentiometer WITH pwm from MG2In Vitamins for the K40 · 3 years ago
Potentiometer needed with mini gerbil?In Vitamins for the K40 · 6 years ago
Cloudray 50w psuIn MG3 installation · 3 years ago
PWM connection for installation into a Ten High 40 watt co2 engraverIn Installation issues · 3 years ago
MG3 Controller IssuesIn Help with installing the Gerbil controller · 3 years ago
x and y swappedIn Help with installing the Gerbil controller · 3 years ago
Inherited a k40 custom laser with an awesome tech. Have some limit switch issues to start.In Help with installing the Gerbil controller · 3 years ago
Help with installation 5v wire problemIn Help with installing the Gerbil controller · 4 years ago
Help with installationIn Troubleshooting · 4 years ago
Help with installationIn Help with installing the Gerbil controller · 4 years ago
Board detection and Lightburn re-homing differences between MG2 and MG3.In Other issues or suggestions · 4 years ago
Laser fires as soon as lid closedIn Other issues or suggestions · 4 years ago
Page 1 of 12Next
Mark All Read

Forum Registration

EDIT YOUR PROFILE HERE