EDIT YOUR PROFILE HERE

Forum breadcrumbs - You are here:ForumUnread Topics
Please or Register to create posts and topics.

Unread Topics

PreviousPage 5 of 12Next
Mark All Read
Unable to increase power above 20%In Fine Tuning performance · 6 years ago
PWM Control issues (laser is firing more than set in software)In Help with installing the Gerbil controller · 6 years ago
HPC LS3020In Help with installing the Gerbil controller · 6 years ago
M3=off M4=onIn All things related to legacy Gerbils · 6 years ago
Mini Gerbil beginner issues (Optical End stops, No working firmware, Unlocking Laser motors)In Help with installing the Gerbil controller · 6 years ago
Will the Gerbil work with my hardware?In Help with installing the Gerbil controller · 6 years ago
Need Help with Homing IssueIn Fine Tuning performance · 7 years ago
Hard set maximum PSU powerIn Installation issues · 6 years ago
Higher Laser Power setting causing stepper motors to loose stepsIn All things related to legacy Gerbils · 7 years ago
check door alarm?In What does alarm <n> mean? · 6 years ago
gerbil mini connectionIn Help with installing the Gerbil controller · 6 years ago
jerkingIn Other issues or suggestions · 6 years ago
TMC2100 Stepper DriversIn Other issues or suggestions · 8 years ago
air assist tube sizeIn Other issues or suggestions · 7 years ago
usb timeoutIn Other issues or suggestions · 7 years ago
16mm LED button and On/Off switchesIn Vitamins for the K40 · 7 years ago
Laser not shutting off on movesIn Other issues or suggestions · 6 years ago
MA staying around 12-14In Installation issues · 6 years ago
machine won't turn onIn Other issues or suggestions · 6 years ago
troubleshootingIn Troubleshooting chart · 6 years ago
Mini Gerbil issues after sparking/new psuIn Help with installing the Gerbil controller · 7 years ago
where to find parts for power connector ?In Installation issues · 7 years ago
No laser powerIn Installation issues · 7 years ago
16 bit pwm upgrade for k40In Installation issues · 6 years ago
need help MiniGerbil does not workIn Installation issues · 6 years ago
Griding motors on non-ribbon k40 versionIn Installation issues · 6 years ago
Install Instructions for Older Version Still Available?In Help with installing the Gerbil controller · 6 years ago
Lightburn not firing my K40In Help with installing the Gerbil controller · 6 years ago
External 24V PSU Issue - No motor movementIn Installation issues · 6 years ago
HY-T50 power supply problemIn Installation issues · 6 years ago
Error codesIn What does alarm <n> mean? · 7 years ago
'switch machine' switch????In Other issues or suggestions · 7 years ago
Mini GRBL Not FoundIn Help with installing the Gerbil controller · 7 years ago
adjustable bed(?)In Other issues or suggestions · 7 years ago
installing on Linux / ubuntuIn Installation issues · 7 years ago
can't open co2 lidIn Other issues or suggestions · 7 years ago
Legacy Gerbil GRBL-M3 No Laser ON with M3In All things related to legacy Gerbils · 7 years ago
Settings Within LightbrunIn Help with installing the Gerbil controller · 7 years ago
error code 9 (end stop)In What does alarm <n> mean? · 7 years ago
No ribbon cable and newer mini gerbil with a few other questions.In Installation issues · 7 years ago
Y-Axis connector issues...In Installation issues · 7 years ago
No homing on extensionIn Inkscape plugin installation issues WIN10 · 7 years ago
Optical Limit Switches Not WorkingIn What does alarm <n> mean? · 7 years ago
Laser power doesn't seem to adjustIn Installation issues · 7 years ago
Custom PWM wireIn Help with installing the Gerbil controller · 7 years ago
Mini Gerbil doesn't connectIn Installation issues · 7 years ago
Gerbil not giving welcome messageIn Help with installing the Gerbil controller · 7 years ago
[Solved] Mini not workingIn Help with installing the Gerbil controller · 7 years ago
.In Help with installing the Gerbil controller · 7 years ago
SpeedIn Fine Tuning performance · 7 years ago
PreviousPage 5 of 12Next
Mark All Read

Forum Registration

EDIT YOUR PROFILE HERE