Forum Navigation
Post History: Paul

No worries Nev, we get you a replacement. It could be the onboard fuse that has triggered because of …In: No Movement from Steppers
2 weeks ago
Hi Nev,
This is a bit of a tricky one, I cannot see any issues with the power connection (24V yel …In: No Movement from Steppers
3 weeks ago
Hi Nerv,
probably better to post some photos of the installation showing the wiring. Most likely …In: No Movement from Steppers
3 weeks ago
Hi Mal,
The PWM output pin on the MG3 provides a 5V PWM signal. Basically its a pulse width varia …In: Low laser power output from Lightburn via MG3
3 months ago
Drag chains are use for cable management, in other words, cable don't get in the way of the mov …In: Photo's of the drag chain installed
3 months ago
3 months ago
Yes you should be able to use the power from the laser supply. The M7 signal goes from the MCU to an …In: What are the best point to source power?
3 months ago
Well done! Sometimes it can be tricky with Windows. Some Windows laptop make a port go sleep to save …In: Ummm Help? Stream not completing
3 months ago
4 months ago
Hi Keith,
In Lightburn you can enable or disable the homing at power on/connecting. See edit/devi …In: On-device head positioning.
4 months ago
Hi Thanks for that.
I can see the safety protect K connector above the D+ and D- connec …In: Different K40 with different wiring
4 months ago
Yes you need the second PSU because that's delivering power to the steppers. The MG3 board need …In: Different K40 with different wiring
4 months ago
The P+ and Ground is just a jumper between the two terminals. Normally this is a switch on the contr …In: Different K40 with different wiring
4 months ago
The failing on any gcode might be the issue. Do you use the correct device "stm gerbil" an …In: Ummm Help? Stream not completing
4 months ago
My panel also has interior light and main power switches. The light works as expected, but if the un …In: k40 with digital control panel questions
4 months ago
Hi,
This can be anything but will list here my things that can happen;
Electrical …In: Ummm Help? Stream not completing
4 months ago
That's good news, the step stick has to be replaced. Just send an email to our support and they …In: No voltage to stepper motors 2-25-2025
4 months ago
Ok from the led statuses I can see that the board does get 5vdc and 24vdc. The limit switches do wor …In: No voltage to stepper motors 2-25-2025
4 months ago
Hi, are you able to provide some more specific details?
Like whether the motor are locked or not? …In: No voltage to stepper motors 2-25-2025
4 months ago
Yes there is an output pin that can use the gcode command M7 or M8. Current the output pin is set to …In: targeting laser
7 months ago
Basically you need TMC stepsticks for zero limit switches. They use firmware to detect a stalled mot …In: Photo's of the drag chain installed
7 months ago
Humm, when the mount end it's on the gantry bar end (right side/not the lens side left) than it …In: Photo's of the drag chain installed
7 months ago
Hi, Thanks for sending the YT video. Apologies for the late reply but we have been debating about th …In: mini Gerbel firing before job
1 year ago
Hi Dave,
This is possible but it requires a bit of tech savviness on your side. Here is the link …In: Air assist solenoid valve
1 year ago
Hi, the laser power is controlled via G code commands e.g. S100 will send 10% power, S500 will send …In: MiniGerbil - Test Fire too Hot
1 year ago
Hi Matteo,
From what I see is that you have an additional power supply. The reason for that is, t …In: Different K40 with different wiring
1 year ago
Hi Matteo,
It seems you have a very new Chinese controller board but the laser power su …In: Different K40 with different wiring
1 year ago
Hi Zoltan,
The results in x and y direction are different because the max stepping rate in x dire …In: Engraviring problem
1 year ago
Hi Derrick, The MG3 differs from MG2 in a way that the power circuits are not shared as in MG2.
M …In: Board detection and Lightburn re-homing differences between MG2 and MG3.
3 years ago
Hi Milos, thanks for reaching out to us. The PSU is not the same but still can be used with the MG3. …In: Help with installation
3 years ago
Hi Wicus, the $ settings between the MG2 and MG3 product are slightly different. We apologise for th …In: 60Watt Install
3 years ago
Hi Wicus, I suspect the logic levels of the limit switches are not good enough to pull the limits.
…In: 60Watt Install
3 years ago
The pull off distance of the limit switches can be set via $27. Normally set to 4mm but you can try …In: 60Watt Install
3 years ago
Hi Wicus, the WP input on the Laser Power supply should be grounded (probably via the safety key) in …In: 60Watt Install
3 years ago
3 years ago
I had a customer with some issues to get his engraving to work. This is a complex process and we wro …In: Engraving quality, ImagR-Kasia
3 years ago
In a nutshell: reduced noise from the power supply by using Optocouplers, increased gantry speed, l …In: MG2 to MG3
3 years ago
If you cannot find the answer here or it is more K40 user related tips (first use, power supply issu …In: Other K40 forums that might be helpful
3 years ago
You can extend the rails in the K40 and use the existing stepper motors. Just adjust the x and y axi …In: External Stepper Drivers MG3
3 years ago
Just read a great post about laser banding (dark and light bands in the engraving)
See this link …In: Laser Banding
3 years ago
If you encounter any issues with MG3 , you could start here MG3 troubleshootingIn: MG3 trouble shooting
3 years ago
There is a blog about customising the air assist port see MG3 Air assist
There are two commands i …In: Customisation Air assist port
3 years ago
Hi David,
You could try Aliexpress https://www.aliexpress.com/item/32785321586.html?spm=a2g0o.sto …In: K40 Stepper Motor
3 years ago
Hi Merv,
This is an excellent question and many beginners bump into this issue. The first thought …In: Grayscale
3 years ago
3 years ago
Just letting you all know that LaserGrbl 4.7.1 seems to work with MGs when set for smoothie device. …In: LaserGrbl 4.7.1 works with smoothie setting
3 years ago
We expect a new batch this week, so it will be available within a week or twoIn: Stock Availability?
4 years ago
We encountered an issue while testing our new controllers with the Y axis being shrunken.
After c …In: Y axis is shrunken when I draw a perfect square
4 years ago