Forum Navigation
Post History: fforsito
Quote from Paul DeGroot on November 26, 2019, 11:17 am
also experiment with rapid speed settings.
…In: Reduce travel movement speed
4 years ago
Hi.
How could I reduce the travel speed? It gives me a lot of vibration in the machine, for examp …In: Reduce travel movement speed
4 years ago
4 years ago
4 years ago
Hi. I am trying to update the minigerbil, I have the st-link v2 and the Stm32 st-link utility softwa …In: Problem update Firmware
4 years ago
Hi.
I need to get the 4-pin minigerbil board power connector (the one that comes original with th …In: Economical power connector
4 years ago
Quote from Paul DeGroot on October 22, 2019, 7:32 am
Probably it's a dirty 5V line (electrical …In: Problem with 5V from power supply
5 years ago
Paul, I discovered the error of so much failure and it is to feed the source with the 5V from the po …In: Update firmware
5 years ago
Hi.
I have a connection problem, after so many errors thinking about updating and others, I have …In: Problem with 5V from power supply
5 years ago
Quote from Paul DeGroot on October 20, 2019, 2:26 pm
You probably need to ground the Door pin on th …In: Update firmware
5 years ago
@paul
Could you please guide me ?, I have many problems with open door error, error 1, …In: Update firmware
5 years ago
Could someone tell me the steps to follow and what do you need to connect to know how to update the …In: Update firmware
5 years ago
I've been trying to connect the gerbil with the STlink for 2 days and I don't know what pi …In: Update firmware
5 years ago
Hi.
I have received the ST Link V2 as the one attached. Could you tell me which pins I should con …In: Update firmware
5 years ago
5 years ago
Paul, it seems that I have already found the fault.
The following must be changed in GRBL:
$ 5 …In: Problem with alternative EndStop
5 years ago
Quote from Paul DeGroot on September 13, 2019, 10:20 am
Ignore the blue arrows, it's a photo f …In: Find DIR, STEP and PUL pins and update firmware?
5 years ago
Quote from Paul DeGroot on September 14, 2019, 12:26 pm
First picture should work but don't br …In: Problem with alternative EndStop
5 years ago
Quote from Paul DeGroot on September 14, 2019, 9:20 am
Hi, the issue with these endstops is that th …In: Problem with alternative EndStop
5 years ago
Hello again 🙂
I am having trouble connecting alternative endstops, they would be the following:
…In: Problem with alternative EndStop
5 years ago
Quote from Paul DeGroot on September 13, 2019, 10:19 am
Hi, the pins are available on the driver so …In: Find DIR, STEP and PUL pins and update firmware?
5 years ago
To not open two separate threads, I prefer to ask in it.
I have some TB6600 as I mentioned in thi …In: Find DIR, STEP and PUL pins and update firmware?
5 years ago
I have the TB6600 at home and I want to connect them to the minigerbil but I can't know where . …In: Install Drivers TB6600
5 years ago
5 years ago
Thanks for the reply. I already have the TB6600 on the way, I imagine that I must configure them in …In: Install Drivers TB6600
5 years ago
5 years ago
Hi. I have broken one of the sides of the box of the minigerbil ... Could you pass me the design in …In: My box has broken
5 years ago
Hi.
Is it possible to connect the minigerbil to some TB6600 drivers ?, I want to put some nema17 …In: Install Drivers TB6600
5 years ago
Hi. I am extending my K40 to this model: http://replicantfx.com/k40-laser-cutter-rebuild-12x24in-2/ …In: Install two nema17
5 years ago
Hi.
In Lighburn, if I select the grayscale option, when I start it starts slow and sometimes it&# …In: Slow speed in grayscale
5 years ago
I've solved it, it was the cable ...
But I have another error, when starting work, it stays …In: Error in lighburn when starting work or going to origin
5 years ago
I have a problem when using Lighburn, when I move manually I have no problem, even the home does it …In: Error in lighburn when starting work or going to origin
5 years ago
5 years ago
According to the connection scheme, all the pins coincide, attached images.
The only di …In: Install two nema17
5 years ago
Thanks for the reply.
What do you mean with bridges MS1,2,3? Should I change something …In: Install two nema17
5 years ago
I connect the X with the flex cable (ribbon) , I would be free the connection I indicated on the boa …In: Install two nema17
5 years ago
Hello. I am expanding the k40 and I want to install the MiniGerbil, I would like to put 2 nema17 mo …In: Install two nema17
5 years ago
Quote from Paul DeGroot on April 29, 2019, 9:58 am
You're welcome ! I just looked up your parc …In: Delivery time in Spain
5 years ago