Update firmware
Quote from fforsito on October 1, 2019, 1:24 amHi.
I have received the ST Link V2 as the one attached. Could you tell me which pins I should connect or if there is any manual on the network to update the Mgerbil firmware?
Thank you
Hi.
I have received the ST Link V2 as the one attached. Could you tell me which pins I should connect or if there is any manual on the network to update the Mgerbil firmware?
Thank you
Uploaded files:
Quote from fforsito on October 4, 2019, 9:31 pmI've been trying to connect the gerbil with the STlink for 2 days and I don't know what pins they are in order to update. or if they have any manual, it would also be worth
I've been trying to connect the gerbil with the STlink for 2 days and I don't know what pins they are in order to update. or if they have any manual, it would also be worth
Quote from fforsito on October 16, 2019, 1:07 pmCould someone tell me the steps to follow and what do you need to connect to know how to update the minigerbil?
Could someone tell me the steps to follow and what do you need to connect to know how to update the minigerbil?
Quote from fforsito on October 20, 2019, 1:21 pm@paul
Could you please guide me ?, I have many problems with open door error, error 1, error 2, etc. with the gerbil and lightburn, however if I select GRBL mode in lightburn there is no problem and that is why I want to update because it is a problem software or firmware because if I select Gerbil mode in lightburn, these errors occur.
Can you tell me how to connect to stlink v2?
Could you please guide me ?, I have many problems with open door error, error 1, error 2, etc. with the gerbil and lightburn, however if I select GRBL mode in lightburn there is no problem and that is why I want to update because it is a problem software or firmware because if I select Gerbil mode in lightburn, these errors occur.
Can you tell me how to connect to stlink v2?
Quote from Paul on October 20, 2019, 2:26 pmYou probably need to ground the Door pin on the controller to get rid off the message.
You probably need to ground the Door pin on the controller to get rid off the message.
Uploaded files:
Quote from fforsito on October 20, 2019, 10:56 pmQuote from Paul DeGroot on October 20, 2019, 2:26 pmYou probably need to ground the Door pin on the controller to get rid off the message.
I have set the door pin to GND and as soon as I turn on, the open door warning skips
If I leave it without GND it works but as soon as it is working, the error of the open door jumps
Grbl 1.1f ['$' for help]
[MSG:Check Door
Quote from Paul DeGroot on October 20, 2019, 2:26 pmYou probably need to ground the Door pin on the controller to get rid off the message.
I have set the door pin to GND and as soon as I turn on, the open door warning skips
If I leave it without GND it works but as soon as it is working, the error of the open door jumps
Grbl 1.1f ['$' for help]
[MSG:Check Door
Quote from fforsito on October 21, 2019, 6:20 amPaul, I discovered the error of so much failure and it is to feed the source with the 5V from the power supply, I leave here the new post with the fault that I think is the problem:
https://awesometech1.wpengine.com/k40-forum/topic/problem-with-5v-from-power-supply/#postid-1359
Paul, I discovered the error of so much failure and it is to feed the source with the 5V from the power supply, I leave here the new post with the fault that I think is the problem:
https://awesometech1.wpengine.com/k40-forum/topic/problem-with-5v-from-power-supply/#postid-1359